Browning AB3 Integrated Scope Mount/Ring Combo Matte Black 1" High 12313

Mount larger optics on your rifle with a clean, rifle-specific setup using the Browning AB3 Integrated Scope Mount/Ring Combo in matte black, configured for 1-inch scope tubes in a high height profile. Identified by part number 12313 and UPC 023614408505, this integrated ring/base solution is designed specifically for Browning AB3 rifles, helping streamline scope installation by combining the base and rings into a matched system. If you’re searching for Browning AB3 1-inch high rings, an AB3 integrated scope mount, or Browning 12313 scope mount rings, this model is built around compatibility, clearance, and repeatable alignment. Integrated Base + Rings: Simplified Mounting with Fewer Variables Instead of mixing separate bases and rings from different product lines, an integrated mount/ring combo reduces the number of interfaces in the scope mounting stack. In practical use, this can help: Reduce the chance of tolerance stacking and misalignment Simplify installation with matched components Provide a cleaner, more unified mounting profile Support consistent ring placement and receiver fit For shooters who want a straightforward AB3-compatible optic mounting option, integrated systems are often chosen for their simplicity and predictable fit. Made for Browning AB3 Rifles This mount/ring combo is designed for the Browning AB3 platform. Because receiver drilling patterns and mounting geometry vary across rifle models, AB3-specific hardware helps ensure: Correct receiver interface alignment Proper fastener and base geometry matching Less guesswork when selecting compatible mounts Always confirm your rifle is a Browning AB3 and verify any receiver variants or special configurations before installation. 1" Ring Diameter: Common Scope Tube Standard This model is built for 1-inch scope tubes, a widely used diameter across many hunting and general-purpose riflescopes. If your optic has a 1" main tube, these rings are designed to clamp correctly without inserts or adapters, supporting straightforward setup and consistent torque across the ring caps. Common searches this fits: AB3 1 inch scope rings Browning AB3 integrated rings 1” Browning 12313 scope mount High Height: Clearance for Larger Objectives and Accessories The high ring height is typically selected when additional clearance is needed for: Larger objective bell diameters Heavier barrel contours Use of scope caps or flip covers Certain bolt handle clearance or optic positioning preferences (rifle-dependent) Because objective sizes vary widely—and “50mm” objectives can differ significantly in outside diameter depending on scope design—users commonly measure actual objective OD and account for caps when selecting ring height. High rings can also influence cheek weld height, so some shooters pair taller rings with stock fit adjustments if needed. Matte Black Finish: Low-Glare, Field-Friendly Appearance The matte black finish provides a subdued, low-reflection surface that matches many rifle receivers and optics. Matte finishes are commonly used in field rifles because they: Reduce glare in bright conditions Blend well with other black-finished components Hide minor handling marks better than glossy finishes For hunting and outdoor use, low-glare surfaces are a practical choice. Why a Solid Mount Matters for Repeatable Zero A mount/ring system is the foundation of your optic setup. A properly installed, correctly torqued mounting system supports: Stable scope position under recoil and transport vibration Repeatable point of impact and consistent zero Proper leveling and alignment of reticle and scope body Reduced chance of ring slip or scope tube stress when installed correctly Even high-quality optics can underperform if the mounting interface shifts, so careful mounting practices matter. Installation and Setup Notes While exact procedures depend on the rifle and manufacturer guidance, common best practices include: Ensure the firearm is unloaded and safe before beginning work Clean mounting surfaces and screw threads to remove oil and debris Follow Browning-recommended torque specs for base and ring screws Set eye relief and level the reticle before final tightening Re-check fastener torque after the first range session If you’re unsure about torque values, alignment, or ring height selection, a qualified gunsmith can help ensure a correct, repeatable installation. Product Identification for Ordering and Inventory Brand: Browning Fits: Browning AB3 Type: Integrated scope mount/ring combo Finish: Matte Black Ring Diameter: 1" Ring Height: High Part Number: 12313 UPC: 023614408505 Ideal For The Browning AB3 Integrated Scope Mount/Ring Combo 12313 is a practical option for users who need: AB3-specific mounting hardware 1-inch scope tube compatibility High ring height for larger objectives or extra clearance A clean, durable matte black finish If you’re setting up a Browning AB3 with a 1" scope and want extra clearance without mixing multiple mounting components, this integrated high ring/mount combo provides a straightforward platform-specific solution. The End