Energetic Armament TB Mount – 1.375×24 (HUB) Thread Pattern – Compatible with Threaded Muzzle Devices – Titanium – Black DLC Finish (EA37) – UPC 853406008374

Expand your suppressor mounting options with uncompromising alignment and minimal weight. The Energetic Armament TB Mount (EA37) is a premium, titanium-machined mount that interfaces with the industry-standard 1.375×24 “HUB” rear thread pattern and is compatible with threaded muzzle devices (per device/manufacturer guidance). A hard-wearing, low-friction black DLC (Diamond-Like Carbon) finish resists carbon, heat, and abrasion, helping the mount install and remove smoothly while maintaining concentricity and repeatable zero.

Why HUB (1.375×24)? It’s the most widely adopted universal rear thread in modern suppressors, unlocking cross-brand compatibility with numerous cans and accessory ecosystems—without locking you into one proprietary system.

Key Benefits

• Precision, repeatable alignment: Tight-tolerance, titanium construction helps preserve bore concentricity and POI stability when mounting to properly threaded muzzle devices.

• HUB ecosystem flexibility: Use one mount across multiple 1.375×24 suppressors and modular systems for simplified kitting.

• Lightweight strength: Titanium delivers outstanding strength-to-weight so you keep your rifle lively while adding durability where it counts.

• DLC surface advantage: The black DLC finish provides a slick, carbon-resistant surface that eases install/removal and withstands heat cycles.

• Built for hard use: Corrosion-resistant materials and finishes stand up to weather, solvents, and high round counts.

Feature Highlights

• Thread Pattern (rear): 1.375×24 (HUB) to fit many contemporary suppressors/modular systems

• Front Interface: Compatible with threaded muzzle devices (consult device maker for geometry/shoulder requirements)

• Material: Titanium (CNC-machined)

• Finish: Black DLC (Diamond-Like Carbon)

• Profile: Compact, weight-conscious design to keep overall length and front-end mass down

• Model / SKU: EA37

• UPC: 853406008374

Compatibility depends on the specific muzzle device’s thread spec, shoulder geometry, and manufacturer guidance. Always verify fit and clearances before live fire.

Ideal Use Cases

• Precision & hunting rifles: Direct, concentric mounting for consistent dope and minimal shift between on/off cycles.

• Suppressed carbines: Keep balance and handling intact while leveraging your preferred threaded muzzle device.

• Multi-host setups: Standardize on HUB to share suppressors and mounts across different rifles and calibers.

Installation (Quick Start)

1. Verify specs: Confirm your suppressor’s rear interface is 1.375×24 and your muzzle device provides the correct thread/shoulder for this mount.

2. Clean & inspect: Degrease mating threads and shoulders; remove carbon and old thread locker.

3. Hand-start only: Thread by hand to avoid cross-threading; torque to manufacturer specs.

4. Bore check: With the bolt removed, visually confirm a clear, centered bore through the mount and suppressor.

5. Heat-cycle verify: After the first range session, re-check torque and witness marks; address any movement before continued use.

Pro Tip: Apply a small, high-temp non-permanent thread locker (e.g., Rocksett®) if recommended by your suppressor/mount manufacturer to counter heat and vibration.

Performance You’ll Notice

• Repeatable zero: Precision threads and rigid titanium body support consistent on/off behavior.

• Reduced carbon stick: DLC’s low-friction surface helps prevent carbon locking and eases cleanup.

• Low mass, high confidence: Keep rifle harmonics predictable and front-end weight minimal.

Compatibility Guidance

• Suppressors/Back Ends: Systems using 1.375×24 (HUB) rear threads.

• Muzzle Devices: Threaded muzzle devices compatible with this mount’s front thread/shoulder requirements; confirm device maker’s instructions.

• Barrel Shoulders: A square, true shoulder is essential for alignment. Use shims/collars only as directed by the device manufacturer.

Care & Maintenance

• Post-range cleanup: Allow to cool, then brush threads with nylon/bronze and use a carbon-safe solvent.

• Avoid galling: Start clean, dry threads by hand; a light oil film for storage prevents corrosion.

• Periodic inspection: Check for wear, nicks, or abnormal marks; service before the next session.

Responsible Use & Legal

• Know your laws: Suppressors and related components may be restricted. Ensure federal, state, and local compliance (NFA where applicable).

• Safety first: Re-check bore alignment anytime you alter mounts, adapters, or muzzle devices.

• Gunsmithing help: Consult a qualified gunsmith if you are unsure about thread spec, shoulder geometry, or fitment.

Specifications (At-a-Glance)

• Product: Energetic Armament TB Mount

• Rear Thread Pattern: 1.375×24 (HUB)

• Front Interface: Compatible with threaded muzzle devices (verify device spec)

• Material: Titanium

• Finish: Black DLC (Diamond-Like Carbon)

• Model: EA37

• UPC: 853406008374

SEO Highlights (Quick Scan)

• Energetic Armament TB Mount EA37

• 1.375×24 HUB thread pattern, titanium construction

• Black DLC finish, compatible with threaded muzzle devices

• Precision alignment, repeatable zero, carbon-resistant surface

• Model EA37, UPC 853406008374

Suggested Meta Title

Energetic Armament TB Mount – 1.375×24 HUB, Titanium, Black DLC – Compatible with Threaded Muzzle Devices | EA37 | UPC 853406008374

Suggested Meta Description

Standardize your suppressor setup with the Energetic Armament TB Mount. Titanium, black DLC mount with 1.375×24 (HUB) threads, compatible with threaded muzzle devices for precise, repeatable alignment. Model EA37, UPC 853406008374.

The End