Jk Armament 155HD Thread Mount 1/2x26 JK155HDM1236

JK Armament 155HD Thread Mount – 1/2×26 – JK155HDM1236 – UPC 850017729308 Lock in rock-solid, repeatable suppressor alignment with the JK Armament 155HD Thread Mount in 1/2×26. Purpose-built for the JK 155HD modular suppressor system, Model JK155HDM1236 (UPC 850017729308) delivers a simple, lightweight, and highly concentric direct-thread interface that shooters trust for accuracy, reliability, and a compact overall profile. If you prefer direct-thread over QD for its weight savings and return-to-zero consistency, this mount is the right tool for the job. Why direct-thread for the 155HD? Fewer moving parts means less weight, lower stack height, and repeatable zero when you remove and reinstall your can. It’s a favorite among precision shooters, hunters, and anyone who values consistent POI. Key Benefits Concentric, secure interface: Tight-tolerance machining supports true bore alignment, helping protect baffles and minimize POI shift. Compact & lightweight: Keeps your suppressor setup trim without bulky adapters, ideal for field carry and long training days. Rugged materials & finish: Precision-machined metal construction with a corrosion-resistant exterior stands up to carbon, heat, and weather. Fast swap capability: Thread off your existing mount and install this 1/2×26 unit to run additional hosts with the same can. Clean aesthetic: Low-profile geometry blends seamlessly with the 155HD for a professional look. Feature Highlights Platform: JK Armament 155HD modular suppressor system Mount Type: Direct-thread (barrel-to-suppressor) Barrel Thread Spec: 1/2×26 (RH) Construction: Precision-machined, corrosion-resistant finish Intended Use: Hunting, precision, training, and general-purpose suppressed shooting Model / SKU: JK155HDM1236 UPC: 850017729308 Always verify your barrel thread pitch (1/2×26) and that your muzzle shoulder is true and square before installation. Ideal Use Cases Precision & hunting rifles/carbines: Direct-thread repeatability supports stable dope and confident cold-bore shots. Range & training hosts: Lightweight setup that reduces front-end mass and keeps handling lively. Multi-host shooters: Easily convert additional 1/2×26 barrels to the 155HD ecosystem without re-zeroing a QD device. Installation (Quick Start) Confirm compatibility: Barrel 1/2×26 threads; suppressor: JK 155HD. Prep threads & shoulder: Degrease the barrel threads/shoulder and the mount; remove old carbon or thread compound. Hand-start only: Thread the mount onto the barrel by hand to prevent cross-threading. Torque & locker: Follow JK Armament torque guidance. If specified, use a high-temp, non-permanent thread locker (e.g., Rocksett®) per manufacturer instructions. Bore check: With bolt removed, visually confirm clear, concentric alignment through the mount and suppressor before firing. Witness mark: Add a small mark across the mount and barrel shoulder to spot any rotation during early heat cycles. Pro Tip: Re-verify torque and alignment after your first range session or any hard use/heat cycles. On-Range Advantages Repeatable zero: Direct-thread design helps your rifle return to zero after removal/installation. Reduced weight & length: Keeps the system slim for better balance and carry comfort. Confidence under heat: Properly torqued mounts resist loosening through extended strings. Care & Maintenance Post-range: Allow to cool, then break carbon with a nylon/bronze brush and a carbon-safe solvent. Thread care: Keep threads clean and lightly oiled for storage; avoid abrasive media that can gall mating surfaces. Routine checks: Inspect for wear, nicks, or carbon locking; re-snug to spec if needed. Safety & Legal Bore alignment matters: If you see any eccentricity or contact marks, do not fire until corrected. Know the law: Suppressor use and transport are regulated—comply with all federal, state, and local regulations (NFA where applicable). Gunsmithing help: If you’re unsure about shoulder squareness or torque, consult a qualified gunsmith. Specifications (At-a-Glance) Brand: JK Armament Product: 155HD Thread Mount Thread: 1/2×26 (RH) Type: Direct-thread adapter for JK 155HD suppressor Finish: Corrosion-resistant Model / SKU: JK155HDM1236 UPC: 850017729308 Compatibility Notes Works with barrels cut to 1/2×26 and a true, square shoulder (crucial for concentricity). For alternate thread pitches, use the corresponding JK 155HD thread mount model. Not a QD mount; designed for direct-thread simplicity and repeatability. SEO Highlights (Quick Scan) JK Armament 155HD Thread Mount 1/2×26 Direct-thread adapter for JK 155HD suppressors Concentric alignment, repeatable zero, corrosion-resistant construction JK155HDM1236, UPC 850017729308 Suggested Meta Title JK Armament 155HD Thread Mount – 1/2×26 Direct-Thread Adapter | JK155HDM1236 | UPC 850017729308 Suggested Meta Description Add a precise, lightweight direct-thread interface to your JK 155HD suppressor. The 1/2×26 thread mount delivers concentric alignment, repeatable zero, and rugged reliability. Model JK155HDM1236, UPC 850017729308. The End