Strike Industries Next Generation Squad Weapon (NGSW) – Wire Management Kit – Tan (ARCMSRAIL) – UPC 793811767018
Tame the tangle and run your pressure-pad cables the right way. The Strike Industries NGSW Wire Management Kit in Tan is a purpose-built cable routing solution for modern carbines and light-support platforms. Designed for today’s NGSW-inspired setups—where lasers, white lights, IR illuminators, and dual-lead switches are common—Model ARCMSRAIL (UPC 793811767018) keeps wires secured, protected, and low-profile along your handguard or rail so nothing snags on gear, barricades, or brush.
Why it matters: Clean cable management improves reliability, ergonomics, and safety—no more snag hazards, shifting pressure pads, or loose wires masking your sight picture or obstructing your support-hand grip.
Key Benefits
Zero-snag routing: Purpose-shaped channels and retainers secure switch leads for SureFire®, Crane/Insight, USB-C/USB-Mini, and other common remote cable diameters.
Low-profile control: Keeps wires tight to the rail, preserving a thumb-over-bore or C-clamp grip without hot spots or pressure points.
Modular layout: Multiple pieces let you create straight runs, 90° turns, and drop-downs to your pressure pad—customize for any rail length or device placement.
Heat & impact resistant: Durable polymer composition is built for range heat cycles and everyday abuse without going brittle or gummy.
Field-serviceable: Snap-in/screw-on installation (hardware style depends on rail segment used) for quick reconfiguration when you change lights, lasers, or pad location.
Mission-ready color: Tan finish blends with most FDE/earth-tone rails, lights, stocks, and slings.
Ideal Use Cases
Dual-lead setups: Organize Crane/SureFire dual-wire systems from an AXON/ModButton/UE tailcap cleanly along M-LOK® or Picatinny® real estate.
Night operations & training: Keep IR/visible wiring tidy for faster indexing and fewer distractions under NODs.
Competition & barricade work: Avoid snags when driving the gun through ports, VTAC boards, or vehicle interiors.
Hunting & field carry: Prevent brush from catching on loose cables and pulling your pad or connector loose.
Feature Highlights
Routing options: Straight channels, corner guides, and tie-down points to accommodate top, side, or underside rail runs.
Protective geometry: Rounded edges and recessed paths reduce chafe while shielding insulation from abrasion.
Flexible footprint: Works with common rail types (e.g., M-LOK/Picatinny sections); choose mounting points that match your accessories and grip style.
Reconfigurable: Move pieces as your setup evolves—new pad location, different tailcap, or an added illuminator.
Color: Tan
Model / SKU: ARCMSRAIL
UPC: 793811767018
Exact piece count, shapes, and hardware may vary by production run. Always refer to the package insert for the definitive parts list and mounting method.
What You’ll Notice After Install
Cleaner handguard: Nothing flopping, shifting, or rubbing your support hand.
Faster indexing: Pressure pad stays where you set it, improving consistency during reps and under stress.
Easier maintenance: Channels make it obvious where the wire runs—quick troubleshooting if something loosens.
Installation (Quick Start)
Unload & clear the firearm. Verify cold.
Plan the route: Mock accessory positions—light, laser, and pad—then choose straight/turn pieces to minimize wire length.
Mount pieces: Attach the wire guides to your rail (follow the included instructions for M-LOK or Picatinny).
Lay the cable: Press leads into channels, using provided retainers/tie points to hold tension.
Pad placement: Secure your pad (per pad manufacturer) and confirm comfortable thumb reach from your shooting stance.
Shake & rack test: Move through shooting positions and shoulder transitions; re-snug hardware if anything shifts.
Pro tip: Leave a small service loop at moving interfaces (e.g., at the pad or tailcap) to prevent strain on connectors.
Compatibility Notes
Cables: Fits common remote switch leads for rifle lights/lasers (diameter dependent).
Rails: Intended for modern handguards with M-LOK or Picatinny attachment points/segments where the kit mounts.
Accessories: Works alongside grips, handstops, and QD sling cups—just route around attachment hardware and avoid barrel contact.
Care & Maintenance
Rinse & wipe: Clean dirt and carbon with mild soap/water; avoid harsh solvents on polymer parts.
Periodic check: Inspect clamps/screws during cleaning days and after high-round-count classes.
Seasonal re-route: If you change gloves or pad style in winter/summer, re-position guides for optimal reach.
Safety & Best Practices
Cable clearance: Keep wires away from moving parts, hot gas vents, and muzzle devices.
No over-tension: Secure but don’t crush; overtight routing can damage insulation or connectors.
Confirm function: After routing, test constant & momentary modes on all devices before live fire.
Specifications (At-a-Glance)
Brand: Strike Industries
Product: NGSW Wire Management Kit
Color: Tan
Rail Interface: For modern rifle rails/handguards; supports common attachment patterns
Use Case: Cable routing for lights, lasers, and remote pressure pads
Model / SKU: ARCMSRAIL
UPC: 793811767018
Why Choose Strike Industries for Cable Management?
Thoughtful ergonomics: Designed around real end-user grips and switch placements.
Modular pieces: Configure routes for your exact kit rather than settling for a one-path solution.
Proven durability: Materials selected for heat, impact, and field abuse.
SEO Highlights (Quick Scan)
Strike Industries NGSW Wire Management Kit Tan
ARCMSRAIL, UPC 793811767018
Cable routing for lights/lasers, pressure-pad wire retainers
M-LOK/Picatinny rail compatible, low-profile, snag-free design
Suggested Meta Title
Strike Industries NGSW Wire Management Kit – Tan | ARCMSRAIL | UPC 793811767018
Suggested Meta Description
Clean up your rifle cabling with the Strike Industries NGSW Wire Management Kit in Tan. Low-profile, modular guides secure pressure-pad wires along M-LOK/Picatinny rails for snag-free control. Model ARCMSRAIL, UPC 793811767018.
The End
