Talley Picatinny Rail — Smoked Bronze Cerakote — 0.425" Front / 0.500" Rear — Fits Browning X-Bolt Long Action — 0 MOA — PL0SB735 (UPC: 810301025288)
Upgrade your optics platform with the Talley Picatinny Rail for Browning X-Bolt Long Action rifles. Finished in premium Smoked Bronze Cerakote to match modern X-Bolt colorways, this precision rail features a stepped profile—0.425" front / 0.500" rear—to deliver ideal scope mounting height and ring placement. With a 0 MOA cant for true, all-around zeroing and maximum internal elevation for typical hunting distances, it’s the go-to base for shooters who demand repeatable alignment, clean aesthetics, and field-proven durability.
Why This Rail Belongs on Your X-Bolt
True 0 MOA geometry: Keeps your optic near the middle of its elevation range for broad zeroing flexibility from woods to western ridgelines.
Stepped height profile (0.425"/0.500"): Thoughtful front/rear heights aid bolt clearance, ring alignment, and objective-bell spacing on Long Action receivers.
Smoked Bronze Cerakote: Rugged, corrosion-resistant finish that pairs perfectly with Browning Smoked Bronze factory coatings for a seamless, custom look.
One-piece precision: Continuous MIL-STD-1913 Picatinny rail ensures consistent ring spacing and the strength you need for hard hunts, heavy recoil, or travel.
Talley quality: Trusted machining tolerances and model-specific hardware for rock-solid attachment and return-to-zero confidence.
At a Glance
Platform: Browning X-Bolt Long Action
Cant: 0 MOA
Heights: 0.425" (front) / 0.500" (rear)
Interface: MIL-STD-1913 Picatinny
Finish: Smoked Bronze Cerakote
Part #: PL0SB735
UPC: 810301025288
Brand: Talley
Key Features & Benefits
Optimized ring interface: Standardized cross slots accept most Picatinny-compatible rings and one-piece mounts for hunting or crossover precision optics.
Bolt & objective clearance: The stepped rear height helps with bolt lift/eyepiece clearance, while overall height supports 40–56 mm objectives (confirm with your scope’s outer diameter and barrel contour).
Repeatable alignment: One-piece base minimizes tolerance stacking and keeps rings co-axial, protecting the scope tube and helping maintain point-of-impact.
Weather-hardened finish: Cerakote stands up to rain, dust, sweat, and abrasion—ideal for mountain hunts, predator stands, or long-range varmint trips.
Clean, low-snag silhouette: Radiused edges reduce snags in scabbards, packs, and saddle scabbards.
Ideal Use Cases
Big-game hunting: Keep your turret travel centered while securing today’s lightweight 3–18x and 4–20x scopes.
Predator & varmint: Stable base for daytime LPVOs or higher-mag optics where tracking and repeatability matter.
Range & zero checks: True 0 MOA profile makes confirming zero at common distances quick and intuitive.
Compatibility
Fits: Browning X-Bolt Long Action receivers.
Does not fit: Short / Super Short action footprints or non-X-Bolt rifles.
Rings & mounts: Accepts Picatinny rings/one-piece mounts from most premium brands; choose height to match objective size and cheek weld.
Installation Notes
Safety first: Verify the rifle is unloaded; remove bolt and magazine.
Prep surfaces: Degrease receiver holes and mounting screws; lightly oil where the manufacturer recommends or use approved thread treatment.
Mount & level: Set the rail flush; snug screws in sequence. Install rings and scope, establish eye relief, and level the reticle.
Torque to spec: Tighten base and ring screws to manufacturer-recommended inch-pound values—do not over-torque.
Verify clearance: Cycle the bolt, check ocular/bolt handle and objective/barrel clearance, then bore-sight and confirm zero at the range.
Care & Maintenance
Wipe down the Cerakote finish after wet or dusty hunts.
Keep cross slots clear of grit so rings clamp evenly.
Periodically verify screw torque, especially after airline travel or big temperature swings.
FAQ
Why choose 0 MOA over 20 MOA?
If your primary use is typical hunting distances, 0 MOA keeps your optic in the center of its travel, making zeroing straightforward while still providing ample dialing room for most cartridges.
Will the Smoked Bronze match my rifle?
Yes—Smoked Bronze Cerakote is selected to complement Browning’s Smoked Bronze factory finishes for a cohesive, premium look.
Which ring height should I use?
Match ring height to your scope’s objective outer diameter, barrel contour, and desired cheek weld. The rail’s stepped profile helps with both bolt and objective clearance.
Do I need to bed the base?
Generally not. Talley’s precise machining offers solid receiver fit. If you encounter receiver variance, consult a qualified gunsmith.
Specifications
Brand: Talley
Product: Picatinny Scope Rail
Platform: Browning X-Bolt Long Action
Cant: 0 MOA
Heights: 0.425" front / 0.500" rear
Interface: MIL-STD-1913 Picatinny
Material: Precision-machined alloy
Finish: Smoked Bronze Cerakote
Part #: PL0SB735
UPC: 810301025288
Safety & Setup: Always follow firearm manufacturer guidelines. Confirm proper torque, re-check zero after travel, and adhere to local regulations.
SEO Highlights (Quick Scan)
Talley Picatinny Rail for Browning X-Bolt Long Action
Smoked Bronze Cerakote, 0 MOA, 0.425" front / 0.500" rear
MIL-STD-1913 one-piece base for ring alignment and repeatable zero
PL0SB735, UPC 810301025288
Meta (for SEO)
Meta Title: Talley Picatinny Rail — Smoked Bronze Cerakote, 0 MOA, 0.425"/0.500" — Fits Browning X-Bolt Long Action — PL0SB735, UPC 810301025288
Meta Description: Build a better optics platform with the Talley Picatinny Rail for X-Bolt Long Action. Smoked Bronze Cerakote, 0 MOA, stepped heights 0.425"/0.500", MIL-STD-1913 interface. Part PL0SB735, UPC 810301025288.
The End
