True Precision — Micro Compensator S-Type | Copper Finish | 416R Stainless Steel | 1/2x28 Threads | 9mm / .380 ACP | Model TPSMICROC | UPC 719104540700
Control recoil in an EDC-friendly package and add a custom look while you’re at it. The True Precision Micro Compensator S-Type in Copper brings reliable muzzle-rise reduction to compact and full-size pistols chambered in 9mm or .380 ACP. Precision-machined from premium 416R stainless steel, then finished in an eye-catching copper tone, TPSMICROC (UPC 719104540700) threads directly onto standard 1/2x28 barrels. The result: flatter tracking, faster follow-ups, and a distinctive aesthetic that pairs perfectly with black, FDE, or two-tone builds—without turning your carry pistol into a range-only race gun.
Model/SKU: TPSMICROC
UPC: 719104540700
Material: 416R Stainless Steel (match-grade barrel steel)
Finish: Copper (low-glare, custom look)
Thread Pitch: 1/2x28 RH
Calibers: 9mm / .380 ACP
Type: S-Type Micro Compensator (carry-oriented profile)
Why Choose the True Precision S-Type Micro Comp (Copper)
Real muzzle-rise reduction, micro size
Tuned ports vent gas to counter muzzle climb, helping you stay on the dot/sights and deliver tighter, faster shot strings—with minimal added length.
EDC-ready footprint
The micro S-Type design keeps weight and overall length down, improving compatibility with many open-muzzle holsters so your daily carry stays practical.
416R stainless strength
Built from the same steel used in premium match barrels, the comp resists heat and wear for long-term durability and consistent performance.
Striking copper finish
The copper tone adds a custom, high-contrast look that complements nitride or DLC slides and gives your build a unique signature.
Standard 1/2x28 mounting
Directly installs on most 9mm/.380 threaded pistol barrels—no special adapters required. (Always verify your barrel’s thread pitch and protrusion.)
Note: Comp performance varies with pistol model, recoil spring rate, and ammo. Start with quality factory 115–147 gr 9mm (or standard .380 ACP) and confirm reliability. Some setups benefit from spring tuning—consult your platform’s guidance or a qualified armorer.
Performance You’ll Notice
Flatter recoil impulse for quicker second shots
Easier dot/iron tracking during rapid strings and transitions
Less grip fatigue over long training sessions
Cleaner sight picture thanks to balanced, upward gas management
Ideal Use Cases
Concealed carry pistols with threaded barrels that need subtle control without bulk
Training & high-rep classes where fatigue accumulates fast
Carry Optics practice to build speed while keeping a holsterable footprint
Compact/micro-compact builds where every millimeter counts
Key Features at a Glance
Construction: CNC-machined 416R stainless steel
Finish: Copper (custom aesthetic, low-glare)
Interface: 1/2x28 RH threads (U.S. standard for most 9mm/.380 barrels)
Design: S-Type Micro — minimal added length/weight
Ports: Optimized to mitigate muzzle rise and stabilize sight picture
Install: Simple screw-on; timing/retention per included instructions (verify hardware included)
Compatibility Notes
Fits 9mm/.380 ACP pistols with 1/2x28 threaded barrels and adequate barrel protrusion beyond the slide (Glock, SIG, CZ, M&P, Shadow Systems, etc.).
Works with many open-muzzle holsters; closed-end holsters may require a comp cut.
Tilting-barrel pistols generally run comps well; verify with your model/ammo.
Installation & Setup (Quick Plan)
Ensure unloaded: Remove magazine, lock slide open, visually/physically clear the chamber.
Prep threads: Clean and lightly oil barrel threads; test-fit by hand.
Time & secure:
If shims/crush washer are provided, time the ports per guidance.
If the unit uses set screws/O-ring retention, apply recommended thread locker and torque to spec.
Function check: Confirm full lock-up and that the comp clears slide/frame through recoil.
Range verify: Fire 150–200 rounds of training ammo; confirm reliability, ejection pattern, and POI. Then test your carry load and re-check zero.
Safety Tip: Recheck torque/retention after deep cleans or high round counts. Comps are not suppressors—do not stack devices unless the manufacturer explicitly supports it.
Care & Maintenance
Allow to cool; brush carbon from ports/threads with solvent.
Wipe the exterior with a soft cloth; avoid harsh abrasives to preserve the finish.
Periodically re-torque set screws or re-apply thread locker as recommended.
Frequently Asked Questions
Q: What thread pitch does it use?
A: 1/2x28 RH, the most common standard for 9mm/.380 ACP pistol barrels in the U.S.
Q: Will it fit my pistol?
A: If your barrel is 9mm or .380 with 1/2x28 threads and enough barrel protrusion, it should fit. Confirm slide/frame clearance and holster compatibility.
Q: Do I need a different recoil spring?
A: Many pistols run fine with stock springs. If you experience short-stroking, consider spring tuning appropriate for your platform.
Q: Does a comp increase blast?
A: All compensators redirect gases; expect more lateral blast. Use quality ear/eye protection and be mindful of others on the line.
Q: Is timing hardware included?
A: Packaging may vary. Follow the included instructions for shims, O-rings, or set screws if provided.
Technical Specs (Summary)
SEO Highlights (Naturally Woven)
True Precision micro compensator S-Type, copper finish, 416R stainless pistol comp, 1/2x28 threaded, 9mm/.380 ACP recoil reduction, EDC-friendly compensator, faster follow-up shots, flat-shooting handgun upgrade, TPSMICROC, UPC 719104540700.
Meta for Your Product Page
Meta Title: True Precision Micro Compensator S-Type — Copper, 416R, 1/2x28, 9mm/.380 | TPSMICROC
Meta Description: Compact S-Type micro compensator in a copper finish, CNC-machined from 416R stainless. 1/2x28 threads for 9mm/.380 ACP pistols. Real muzzle-rise reduction with a custom look. SKU TPSMICROC — UPC 719104540700.
From everyday carry to weekend drills, the True Precision Micro Compensator S-Type (Copper) delivers the flat recoil impulse, premium materials, and distinctive style you want—so you can run your pistol faster with confidence.
The End
