True Precision — Micro Compensator S-Type | Satin Stainless | 416R Stainless Steel | 1/2x28 Threads | 9mm / .380 ACP | Model TPSMICROSS | UPC 719104540687
Flatten recoil. Track the dot. Shoot faster with control. The True Precision Micro Compensator S-Type is a compact, carry-focused muzzle device that tames muzzle rise on 9mm and .380 ACP pistols without turning your EDC into a range-only race gun. Precision-machined from 416R stainless steel and finished in a handsome satin stainless sheen, TPSMICROSS (UPC 719104540687) threads directly to standard 1/2x28 pistol barrels and adds minimal length—giving you real-world recoil mitigation with holster-friendly dimensions.
Model/SKU: TPSMICROSS
UPC: 719104540687
Material: 416R stainless steel (match-grade barrel steel)
Finish: Satin stainless (low-glare, easy to clean)
Calibers: 9mm / .380 ACP
Thread Pitch: 1/2x28 (RH)
Type: Micro compensator (S-Type) — compact, carry-oriented profile
Why Choose the True Precision Micro Comp (S-Type)
Real recoil reduction in a micro form factor
Carefully engineered ports redirect gas to counter muzzle climb and keep sights (or dot) flat through the shot, improving split times and shot-to-shot accuracy—without excessive blast or bulk.
EDC-friendly size & weight
The micro profile adds only a modest amount of length/weight to your pistol, preserving holster compatibility with many open-muzzle rigs while delivering measurable control.
416R stainless durability
Built from the same steel used in premium match barrels, the S-Type withstands sustained heat, cleaning cycles, and daily carry with corrosion-resistant confidence.
Sleek satin stainless finish
Low-glare, bead-satin look complements stainless slides, nitride barrels, and two-tone builds—and wipes clean quickly after range sessions.
Standard 1/2x28 mounting
Threads directly to most 9mm/.380 threaded pistol barrels—no special adapters required. (Always confirm your barrel’s pitch before installation.)
Note: Reliability with comps can vary by pistol, recoil spring rate, and ammo. Start with quality factory 115–147gr 9mm (or standard .380 ACP) and confirm function. Some setups benefit from spring tuning—consult your pistol’s platform community or a qualified armorer.
Performance You’ll Notice
Flatter dot/sights under recoil for faster follow-ups
More consistent grip pressure—less effort spent muscling the gun
Cleaner sight picture thanks to balanced, upward gas management
Confidence at speed on transitions, bill drills, and timed stages
Best Use Cases
Concealed carry & duty-sized EDC wanting a subtle control boost
Training and high-rep classes where fatigue adds up
Carry Optics / range practice to build speed without sacrificing carry practicality
Micro/compact pistols with threaded barrels where length matters
Key Features at a Glance
Construction: CNC-machined 416R stainless steel
Finish: Satin stainless (easy to clean, corrosion resistant)
Interface: 1/2x28 right-hand threads (9mm/.380 ACP standard)
Profile: S-Type micro compensator, minimal added length
Ports: Optimized gas redirection to reduce muzzle rise
Install: Simple screw-on fit; uses common timing/retention methods (verify included hardware)
Installation & Setup (Quick Plan)
Verify safe & clear: Remove magazine and clear the chamber.
Prep threads: Ensure barrel threads are clean; test-fit the comp by hand.
Time & secure:
If your pistol/comp uses shims or a crush washer, time the ports per guidance.
If your unit uses set screws/O-ring retention, follow torque and thread-locker recommendations from True Precision.
Function check: Hand-cycle to ensure full lockup and that the comp clears the slide/frame through recoil.
Range verify: Run 150–200 rounds of your training ammo to confirm reliability, ejection pattern, and benefit; then test your carry load.
Suppressor caution: Compensators are not suppressors; do not stack devices unless your platform and device maker explicitly permit it. Always check concentricity and clearance for any stacked setup.
Compatibility Notes
Fits 1/2x28 threaded 9mm/.380 ACP pistol barrels (Glock, SIG, CZ, M&P, etc.) that protrude beyond the slide enough to accept a comp.
Works with most open-muzzle holsters; some enclosed holsters may require a comp-cut.
Tilting-barrel pistols generally run comps well; verify with your model. Sub-compacts may prefer mid-weight loads and proper spring rates.
Care & Maintenance
After shooting, allow to cool; wipe carbon with a nylon brush and solvent.
Inspect ports and threads for fouling; re-apply thread-locker as needed per manufacturer guidance.
Periodically check set screws/timing and re-torque to spec.
Frequently Asked Questions
Q: What’s the thread pitch?
A: 1/2x28 RH, the typical standard for 9mm/.380 ACP pistol barrels in the U.S.
Q: Will it fit my (brand/model) pistol?
A: If your barrel is 9mm or .380 ACP with 1/2x28 threads and enough barrel protrusion, it should fit. Verify slide/frame clearance and holster compatibility.
Q: Do I need new recoil springs?
A: Many pistols run fine stock. If you experience short-stroking or sluggish return, experiment with spring weights recommended for your platform.
Q: Does it require shims?
A: Timing/retention varies by batch and setup. Some comps use shims/crush washer; others rely on set screws or O-rings. Check the included instructions for your unit.
Q: Will it increase blast?
A: All comps redirect gas; you may notice more side blast. Use quality ear pro and be mindful of others on the line.
Specs (Summary)
SEO Highlights (Naturally Woven)
True Precision micro compensator for 9mm/.380 ACP, 1/2x28 threaded pistol comp, 416R stainless, satin stainless finish, S-Type low-profile design, recoil reduction, faster follow-up shots, EDC-friendly, TPSMICROSS, UPC 719104540687.
Meta for Your Product Page
Meta Title: True Precision Micro Compensator S-Type — 416R Satin Stainless, 1/2x28, 9mm/.380 | TPSMICROSS
Meta Description: Compact, carry-friendly micro compensator in 416R satin stainless for 9mm/.380 ACP pistols. 1/2x28 threads, S-Type design, real recoil control with minimal added length. SKU TPSMICROSS — UPC 719104540687.
From daily carry to weekend drills, the True Precision Micro Compensator S-Type delivers flat-shooting control, premium materials, and holster-friendly size—so you can run your pistol faster and more precisely when it matters.
The End
