WIPE-OUT® Brushless Foaming Bore Cleaner
Non-Abrasive, No-Scrub Formula • Expanding Foam Penetrates Rifling • Removes Copper, Carbon & Powder Fouling
UPC: 695791010057 • Part #: 695791010057
Cut your cleaning time and skip the elbow grease. WIPE-OUT® Brushless Foaming Bore Cleaner uses an expanding, brush-free foam to flood your barrel’s rifling, dissolve fouling, and lift it out—no aggressive scrubbing required. Just fill the bore, let the chemistry work, and patch it clean. Designed for shooters who want a thorough, repeatable clean after range days, matches, or hunts, WIPE-OUT leaves barrels bright, consistent, and ready to shoot with minimal effort.
From precision rifles and carbines to handguns and shotguns, this foaming bore cleaner reaches lands, grooves, and hard-to-reach corners to remove copper, carbon, and powder residue that degrade accuracy and velocity. If you’re chasing tighter groups and a consistent cold-bore shot, WIPE-OUT® is the easy button.
Why WIPE-OUT® Brushless Works So Well
Expanding Foam = Full Contact
Fills the bore from throat to crown so the chemistry can act on every surface—rifling, micro-pits, and tight corners that patches and brushes miss.
Brushless, No-Scrub Convenience
No bronze brushes to wear out or damage crowns. Spray, wait, and patch—fast routine that’s easy to repeat after every session.
Multi-Fouling Attack
Formulated to loosen and dissolve copper jacket fouling, carbon, and powder residue, restoring a uniform surface for consistent accuracy.
Non-Abrasive Formula
Cleans chemically rather than mechanically, helping preserve barrel life in match and high-value hunting rifles.
Less Mess, Less Odor
Controlled foam reduces runs and drips; easy wipe-down on mats and benches.
Compatibility: Suitable for rifles, handguns, and shotguns with steel bores. Always follow your firearm manufacturer’s care guidelines and test on a small area before use on specialty finishes.
Key Features at a Glance
Type: Foaming, brushless bore cleaner
Targets: Copper, carbon, and powder fouling
Use: Rifles, pistols, shotguns (centerfire & rimfire)
Application: Fill, wait, patch—repeat as needed
UPC / Part #: 695791010057 / 695791010057
How to Use (Quick Start)
Unload & Verify Clear. Remove magazine, open action, and visually/physically inspect the chamber.
Set Up the Barrel. Place the firearm in a safe, horizontal position. Use a chamber plug or patch at the breech if desired to contain foam.
Apply WIPE-OUT. Insert the nozzle from the chamber end and fill the bore until foam reaches the muzzle.
Let It Work. Allow 15–30 minutes for routine cleaning. For heavy copper, leave it longer (up to several hours/overnight) per label guidance.
Patch It Out. Push clean patches from chamber to muzzle until they come out clean.
Repeat if Needed. Stubborn fouling may require a second application.
Protect the Bore. Follow with a light oil or corrosion inhibitor before storage.
Pro Tip: Clean from the chamber end with a bore guide to protect the crown and maintain alignment in precision barrels.
Best Practices for Accuracy
Establish a Routine: Clean after each session to keep copper and carbon from “baking in.”
Monitor Groups: If your groups open up or the cold-bore shot drifts, a deep de-coppering with WIPE-OUT often restores point of impact.
Condition the Bore: After a deep clean, fire a couple of fouling shots to return to your rifle’s preferred condition before a match or hunt.
Ideal Use Cases
Precision & PRS Rifles: Maintain consistency shot-to-shot by removing thin, accuracy-killing fouling layers.
Hunting Firearms: Quick, thorough clean post-season with minimal scrubbing.
High-Volume Carbines & Pistols: Keep gas systems and bores cleaner for smoother cycling and easier maintenance.
Shotguns: Lift plastic wad fouling and powder residue from smoothbore barrels.
Safety & Care
Use in a well-ventilated area; avoid contact with skin and eyes.
Keep away from wood stocks, optics coatings, and painted surfaces—wipe any overspray immediately.
Do not mix with other chemicals in the bore unless the manufacturer states compatibility.
Store capped, upright, away from heat sources. Keep out of reach of children.
Frequently Asked Questions
Q: Is brushing ever required?
A: For most routine cleanings, no—that’s the point of WIPE-OUT. Extremely heavy, layered fouling may benefit from a nylon brush after the foam has loosened deposits.
Q: Will it harm my barrel steel?
A: The formula is non-abrasive and designed for firearm bores. Follow directions and time limits on the label for best results.
Q: Can I leave it overnight?
A: Many shooters do for heavy copper. Always follow the manufacturer’s maximum dwell guidance and neutralize with patches, then lightly oil.
Q: Does it remove carbon rings at the throat?
A: The expanding foam helps penetrate stubborn carbon. Multiple cycles may be needed on hard rings.
Q: Safe for chrome-lined or nitrided bores?
A: Generally used across common bore finishes. Always test on a small area and follow the firearm maker’s recommendations.
SEO Highlights (Quick Scan)
WIPE-OUT Brushless Foaming Bore Cleaner – no-scrub expanding foam
Removes copper, carbon, and powder fouling for accurate barrels
Non-abrasive cleaning; ideal for rifles, pistols, and shotguns
Easy application: fill, wait, patch; follow with light oil
UPC 695791010057 • Part # 695791010057
The Bottom Line
If you want match-grade clean without the marathon scrubbing session, WIPE-OUT® Brushless Foaming Bore Cleaner delivers. Its expanding foam reaches where brushes can’t, dissolving copper and carbon to restore consistency, accuracy, and confidence—with a simple spray-wait-patch routine you’ll actually keep.
The End
